Sharing is caring!

The presence of trees on one’s property is typically welcomed. However, some trees can be invasive and are a sight for sore eyes to see them take over your garden over time. Trees can also encroach on your property in other scenarios, deepening their roots into the soil or obstructing light within the area. Now, suppose you’re ready to perform tree removal by any means necessary. In that case, you’ll need to consider the available choices you have and make a thoroughly calculated decision on what will be best for you. You can also take the help of tree removal service experts.

Luckily, we’re here to help by telling you some of the necessary steps you’ll need to undergo to get rid of any unwanted trees inside your area. After all, everyone should make it a point to look at the potential impact of a big tree on your house. You can take guidance from Riverside tree experts to remove unwanted trees.

1. Starve the tree 

Trees rely on their bark to transfer nutrients and moisture from within the soil to the different leaves and branches. When the bark encircling the trunk’s circumference is completely removed, the tree is essentially starved to death. Known as “girdling,” the method is usually successful, but not without its flaws. To ensure that you get the best outcome possible, remove all the bark layers encircling the tree with either an ax or a hatchet. The girdle should be around 2 inches in density, while for a big tree, it should reach up to 8 inches in width.

2. Cutting down a tree 

Cutting down a tree has been made easy for you. For starters, you can always hire someone to do the job and cut down the three that’s been bothering you all this time, and you won’t have to bring out the chainsaw by yourself if you’re not experienced using it. On the other hand, lots of people literally let their trees fall. And to do this, you’ll need to shred the tree stump to the very bottom until the tree gets shredded down to a mere stump.

It’s worth noting, however, simply cutting down the tree doesn’t always do the trick and can sometimes leave a small trace. Trees can continue sprouting themselves from their stump, and if something unfortunate like this happens, you’ll have to go through another process of looking for little sprouts and cutting them down as they show up. This way, you deprive the roots of the nutrients it needs to keep growing by getting rid of the tree sprouts. 

You’ll have to dig deep down and scrape the roots within the soil if crushing the stub nor chopping the tree sprouts will be enough to ruin the tree. 

3. Chemical method of killing a tree 

Herbicides can destroy lots of trees while still being environmentally friendly if used correctly. It can be applied to a particular section of a tree, which is the most environment friendly choice. To do this method, fill up a spray bottle or a hose sprayer with a water-soluble herbicide containing glyphosate. Brands such as Garlon 3A, Arsenal, and Roundup Pro are all water-soluble choices.

Next, you need to put the herbicide to the different cuts, putting each one around 1 mL. Sprays should be applied as soon as the tree is cut to prevent a tree from forming a protective layer on the cuts. After all this, if the tree hasn’t died after 5 – 6 weeks, you need to reapply the spray. 

Some Other Tips:

It’s important that you learn how to properly use the herbicides safely and lawfully before beginning the process of any annoying trees in your area. Remember these few tips as well: 

• If you’re using the cutting method, make sure to apply herbicide right away so the tree won’t have time to recover while you can get the most absorption off.

• Roof grafting, a process that mainly happens within the same tree species but may also occur between different ones and the same genus, allows roots to share the same tissues in their vascular section.

• The use of strains or dyes in herbicide solutions improves applicator precision significantly. Applicators use the pigments to keep track of handled plants, making it less likely that they will miss or need to reapply. The presence of stains can show Self-exposure. 

• Your herbicide has the potential to spread from a treated and untreated tree, destroying or damaging the latter. 

• Herbicides should not be used in environments where it damages other kinds of trees or plants. Think of it as the tree growing to a width equal to a tree’s height in hot weather and less distance in colder ones. 

• Once a tree can release herbicides, it may be eligible for another. A tree that’s been treated can release herbicide back into an environment, causing harm to other plants around the area.

Courtney P.

I’m a 20-something stay-at-home mother and wife. I have an amazing husband, a beautiful daughter, two loving dogs, and a lazy cat. I wouldn’t change my life for anything! I love to read, listen to music, cook and blog!

Sharing is caring!